Moin Leute
Die Liebe Post hat es heute Geschafft mir mein Elegoo Uno R3 zu liefern.
Gut dachte ich mir geht bestimmt ganz schnell Arduino an Rechner mit der Arduino Software schnell die Glediator Firmware drauf Gepackt und gut ist.
So also Jinx Geöffnet gekuckt ah super wird erkannt ausgewählt und auf OK Geklickt.
Wäre ja schön wenn es so einfach gegangen wäre!
Was mich Wundert ich habe WS2811 nur an denn Strom Gepackt und Zack fingen sie an zu Leuchten und zwar Weiß.
Ich habe GND und Data Pin 6 vom Arduino zu denn Scripts Gelegt. Eigentlich alles nach Handbuch
Die haben sich auch nicht Gezuckt als ich Jinx geöffnet habe die sind einfach auf weiß Geblieben.
Ein Widerstand 330Ohm Widerstand befindet sich zwischen der Data Leitung.
Ich komme nicht weiter Hilfe
Hier mal der Sketch denn ich auf denn Arduino habe
//##############################################################################
//##############################################################################
// #
// Glediator to WS2812 pixel converter #
// by R. Heller #
// V 1.0 - 07.01.2014 #
// wwww.SolderLab.de #
// #
// Receives serial data in Glediator protocol format @ 1 MBit/s #
// and distributes it to a connectect chain of WS2812 pixels #
// #
// Adjust the correct DATA PIN and the correct NUMBER OF PIXELS you are using #
// in the definitions section below before uploading this sketch to your #
// Arduino device. #
// #
// Maxiumim number of supported pixeles is 512 !!! #
// #
// In the Glediator software set output mode to "Glediator_Protocol", #
// color order to "GRB" and baud rate to "1000000" #
// #
//##############################################################################
//##############################################################################
//##############################################################################
// #
// Definitions --> Make changes ONLY HERE #
// #
// To find out the correct port, ddr and pin name when you just know the #
// Arduino's digital pin number just google for "Arduino pin mapping". #
// In the present example digital Pin 6 is used which corresponds to "PORTD", #
// "DDRD" and "6", respectively. #
// #
//##############################################################################
#define DATA_PORT PORTD
#define DATA_DDR DDRD
#define DATA_PIN 6
#define NUMBER_OF_PIXELS 100
//##############################################################################
// #
// Variables #
// #
//##############################################################################
unsigned char display_buffer[NUMBER_OF_PIXELS * 3];
static unsigned char *ptr;
static unsigned int pos = 0;
volatile unsigned char go = 0;
//##############################################################################
// #
// Setup #
// #
//##############################################################################
void setup()
{
// Set data pin as output
DATA_DDR |= (1 << DATA_PIN);
// Initialize UART
UCSR0A |= (1<<U2X0);
UCSR0B |= (1<<RXEN0) | (1<<TXEN0) | (1<<RXCIE0);
UCSR0C |= (1<<UCSZ01) | (1<<UCSZ00) ;
UBRR0H = 0;
UBRR0L = 1; //Baud Rate 1 MBit (at F_CPU = 16MHz)
ptr=display_buffer;
//Enable global interrupts
sei();
}
//##############################################################################
// #
// Main loop #
// #
//##############################################################################
void loop()
{
if (go==1)
{
cli();
ws2812_sendarray(display_buffer, NUMBER_OF_PIXELS * 3);
sei();
go=0;
}
}
//##############################################################################
// #
// UART-Interrupt-Prozedur (called every time one byte is compeltely received) #
// #
//##############################################################################
ISR(USART_RX_vect)
{
unsigned char b;
b=UDR0;
if (b == 1) {pos=0; ptr=display_buffer; return;}
if (pos == (NUMBER_OF_PIXELS*3)) {} else {*ptr=b; ptr++; pos++;}
if (pos == ((NUMBER_OF_PIXELS*3)-1)) {go=1;}
}
//##############################################################################
// #
// WS2812 output routine #
// Extracted from a ligh weight WS2812 lib by Tim (cpldcpu@gmail.com) #
// Found on wwww.microcontroller.net #
// Requires F_CPU = 16MHz #
// #
//##############################################################################
void ws2812_sendarray(uint8_t *data,uint16_t datlen)
{
uint8_t curbyte,ctr,masklo;
uint8_t maskhi = _BV(DATA_PIN);
masklo =~ maskhi & DATA_PORT;
maskhi |= DATA_PORT;
while (datlen--)
{
curbyte = *data++;
asm volatile
(
" ldi %0,8 \n\t" // 0
"loop%=:out %2, %3 \n\t" // 1
"lsl %1 \n\t" // 2
"dec %0 \n\t" // 3
" rjmp .+0 \n\t" // 5
" brcs .+2 \n\t" // 6l / 7h
" out %2,%4 \n\t" // 7l / -
" rjmp .+0 \n\t" // 9
" nop \n\t" // 10
" out %2,%4 \n\t" // 11
" breq end%= \n\t" // 12 nt. 13 taken
" rjmp .+0 \n\t" // 14
" rjmp .+0 \n\t" // 16
" rjmp .+0 \n\t" // 18
" rjmp loop%= \n\t" // 20
"end%=: \n\t"
: "=&d" (ctr)
: "r" (curbyte), "I" (_SFR_IO_ADDR(DATA_PORT)), "r" (maskhi), "r" (masklo)
);
}
}
//##############################################################################
// #
// End of program #
// #
//##############################################################################
Alles anzeigen